PRODUCTS
- GRP SECTIONAL WATER TANK
- PRESSED STEEL SECTIONAL WATER TANK
- PRESSED STAINLESS STEEL WATER TANK
GENERAL SPECIFICATIONS
Standard:
Singapore Standard SS245: 1995 Cross section to British Standard BS 7491
Part 3:1994 and BS EN 13280:2001
Material:
Resin- Isophthalic unsaturated polyester resin conforming to BC 3532 specification
Fiber Glass- Low alkali fibre glass conforming to JIS R3411 to R3417 or BS 33396, BS 3496 and BS 3749 specifications
Manufacturing Process:
External Reinforcement- Hot dipped galvanised steel lnternal reinforcement-
(1) Standard: SS 304 Tie-Rod or Cleat Angle Stay
(2) Optional: SS 316 Tie-Rod pr Cleat Angle Stay
Optional: Metal-Free internal with special design
External Support For Non-partitioned Tanks:
Roof Support: PVC Vertical Poles and GRP roof panel stiffener
Sealant:
Non toxic PVC foam
Bolt, Nuts, Washers:
External - Standard : Hot Dipped Galvanised Steel
Optional : SS 304/A2 or SS 316/A4
Internal – Standard : SS 304/A2
Optional : SS 316/A4
Ladder :
External – Standard : Hot Dipped Galvanised Steel
Internal – Standard : PVC
Optional : GRP or 316
Water Level Indicator :
Standard Reversed Reading Mechanical Ball Float Type with Mouse
Optional : Direct Reading Clear Tube Type
Nozzle Panel :
Flat panels will be provided for any type of piping materials
The HOT PRESSED (SMC) SHEET MOULDING COMPOUND method is employed to produce the GRP panels in order to ensure dimensional accuracy and consistent mechanical properties. Products produced by this method are used worldwide in a multiplicity of structural and engineering applications. These range from aircraft wings where structural integrity is paramount to ship hulls where a combination of strength and water tightness is fundamental.
- GRP PANEL DESIGN
- GRP PRE--INSULATED PANEL
- SKIN BASE SPECIFICATION
- GRP SECTIONAL WATER TANK
(click picture to enlarge)
Performance of Panels
|
By encapsulating a 25mm ~ 40mm layer of rigid polyurethane foam, PIPECO pre-insulated panel could maintain the desired water temperature stored inside the tank under extreme temperature condition. PIPECO pre-insulated panel could be selected for water storage where there is a need to stabilize the temperature against extreme heat or freezing condition so to prevent dew formation.
(click picture to enlarge)
 |
PIPECO GRP tank installed in Erbil, Iraq which utilized the pre-insulated panels.(click picture to enlarge)
 |
|
Note: *PIPECO reserves the right to provide alternate skid base designs. PIPECO recommends an ideal concrete plinth size of 300mm (W) x 600mm (H), with maximum variance in height of not more than 3mm. |
PIPECO GRP/FRP sectional water tank is constructed with bottom, side and top panels, completes with external and internal structural reinforcement and necessary tank accessories to facilitate water storage.
 |
Blow out view of GRP sectional water tank (click picture to enlarge)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
Mockup display available in Port Klang main factory for customer review (click picture to enlarge)
GENERAL SPECIFICATIONS
Standard:
PIPECO pressed steel sectional water tank constructed with hydraulically pressed flanged panels, conform to BS 1564 : 1975 and SS 22 : 1979
Flanges of Plates :
The tank plates are pressed with a combined double flange at an angle of 45 degree and 90 degree to the face of the plate on four sides
Stays and Cleats :
The stays and cleats are made of steel angle bar and steel plate
Bolts, Nuts and Washers:
Hot Dipped Galvanised steel bolts, nuts and washers for internal and external.
Jointing Materials :
Non toxic PVC foam to be used for all jointing between tank panel flange
Tank Cover :
Panel type tank cover supported by trusses and poles 600 x 600 square manhole and 100mm air-vent supplied as standard for each compartment
Water Level Indicator :
Mechanical Ball Float Type
Ladder :
Alumninium ladder for internal and external
Finish :
(a) Hot Dip Galvanised conform to BS 729 or ISO equivalent
(b) Black Bituminous Coated
Standard Thickness for 1.22m x 1.22m Tank Panel
|
Standard Thickness for 1m x 1m Tank Panel
|
GENERAL SPECIFICATIONS
Standard:
PIPECO pressed steel sectional water tank constructed with hydraulically pressed flanged panels.
Materials:
The tank panel, stays and cleats are made from Stainless Stell Grade 304/316
Flanges of Plates :
The tank plates are pressed with a combined double flange at an angle of 45 degree and 90 degree to the face of the plate on four sides
Bolts, Nuts and Washers:
Stainless Steel Grade304/316 bolts, nuts and washer
Jointing Materials :
Non toxic PVC foam to be used for all jointing between tank panel flange
Tank Cover :
Panel type tank cover supported by trusses and poles 600 x 600 square manhole and supplied as standard for each compartment
Water Level Indicator :
Mechanical Ball Float Type
Nozzles for Connection:
Short pipe with flange or socket for all pipe connections
Ladder :
Internal ladder shall br made of Stainless Steel 304/316 and aluminium for external ladder
Standard Thickness for 1.22m x 1.22m Tank Panel
|
Standard Thickness for 1m x 1m Tank Panel
|
- G
